Ivermectin-Loaded Mesoporous Silica and Polymeric Nanocapsules: Impact on Drug Loading, In Vitro Solubility Enhancement, and Release Performance.

Ivermectin (IVM), a widely used drug for parasitic infections, faces formulation and application challenges due to its poor water solubility and limited bioavailability. Pondering the impact of IVM's high partition coefficient value (log P) on its drug release performance, it is relevant to explore whether IVM nanoencapsulation in organic or inorganic nanoparticles would afford comparable enhanced aqueous solubility. To date, the use of inorganic nanoparticles remains an unexplored approach for delivering IVM. Therefore, here we loaded IVM in mesoporous silica particles (IVM-MCM), as inorganic nanomaterial, and in well-known poly(ε-caprolactone) nanocapsules (IVM-NC). IVM-MCM had a well-organized hexagonal mesoporous structure, reduced surface area, and high drug loading of 10% w/w. IVM-NC had a nanometric mean size (196 nm), high encapsulation efficiency (100%), physicochemical stability as an aqueous dispersion, and drug loading of 0.1% w/w. Despite differing characteristics, both nanoencapsulated forms enhance IVM's aqueous intrinsic solubility compared to a crystalline IVM: after 72 h, IVM-MCM and IVM-NC achieve 72% and 78% releases through a dialysis bag, whereas crystalline IVM dispersion achieves only 40% drug diffusion. These results show distinct controlled release profiles, where IVM-NC provides a deeper sustained controlled release over the whole experiment compared to the inorganic nanomaterial (IVM-MCM). Discussing differences, including drug loading and release kinetics, is crucial for optimizing IVM's therapeutic performance. The study design, combined with administration route plans and safety considerations for humans and animals, may expedite the rational optimization of IVM nanoformulations for swift clinical translation.

Magnetic Mesoporous Silica for Targeted Drug Delivery of Chloroquine: Synthesis, Characterization, and In Vitro Evaluation.

Malaria is a dangerous tropical disease, with high morbidity in developing countries. The responsible parasite has developed resistance to the existing drugs; therefore, new drug delivery systems are being studied to increase efficacy by targeting hemozoin, a parasite paramagnetic metabolite. Herein, magnetic mesoporous silica (magMCM) was synthesized using iron oxide particles dispersed in the silica structure for magnetically driven behavior. The X-ray diffractogram (XRD) and Mössbauer spectra show patterns corresponding to magnetite and maghemite. Furthermore, Mössbauer spectroscopy revealed superparamagnetic behavior, attributed to single magnetic domains in particles smaller than 10 nm. Even in the presence of iron oxide particles, the hexagonal structure of MCM is clearly identified in XRD (low-angle region) and the channels are visible in TEM images. The drug chloroquine (CQ) was encapsulated by incipient wetness impregnation (magMCM-CQ). The N2 adsorption-desorption isotherms show that CQ molecules were encapsulated in the pores, without completely filling the mesopores. BET surface area values were 630 m2 g-1 (magMCM) and 467 m2 g-1 (magMCM-CQ). Encapsulated CQ exhibited rapid delivery (99% in 3 h) in buffer medium and improved solubility compared to the non-encapsulated drug, attributed to CQ encapsulation in amorphous form. The biocompatibility assessment of magMCM, magMCM-CQ, and CQ against MRC5 non-tumoral lung fibroblasts using the MTT assay after 24 h revealed no toxicity associated with magMCM. On the other hand, the non-encapsulated CQ and magMCM-CQ exhibited comparable dose-response activity, indicating a similar cytotoxic effect.

Magnetic core-shell cellulose system for the oriented immobilization of a recombinant ß-galactosidase with a protein tag.

The objective of this study was to immobilize a recombinant ß-galactosidase (Gal) tagged with a cellulose-binding domain (CBD) onto a magnetic core-shell (CS) cellulose system. After 30 min of reaction, 4 U/capsule were immobilized (CS@Gal), resulting in levels of yield and efficiency exceeding 80 %. The optimal temperature for ß-galactosidase-CBD activity increased from 40 to 50 °C following oriented immobilization. The inhibitory effect of galactose decreased in the enzyme reactions catalyzed by CS@Gal, and Mg2+ increased the immobilized enzyme activity by 40 % in the magnetic CS cellulose system. The relative enzyme activity of the CS@Gal was 20 % higher than that of the soluble enzyme activity after 20 min at 50 °C. The CS support and CS@Gal capsules exhibited an average size of 8 ± 1 mm, with the structure of the shell (alginate-pectin-cellulose) enveloping and isolating the magnetic core. The immobilized ß-galactosidase-CBD within the magnetic CS cellulose system retained ∼80 % of its capacity to hydrolyze lactose from skim milk after 10 reuse cycles. This study unveils a novel and promising support for the oriented immobilization of recombinant ß-galactosidase using a magnetic CS system and a CBD tag. This support facilitates ß-galactosidase reuse and efficient separation, consequently enhancing the catalytic properties of the enzyme.

Drug-loaded mesoporous silica on carboxymethyl cellulose hydrogel: Development of innovative 3D printed hydrophilic films.

3D printing has been explored as an emerging technology for the development of versatile and printable materials for drug delivery. However, the alliance of 3D printing and nanomaterials has, to date, been little explored in pharmaceutics. Herein, a mesoporous silica with nanostructured pores, SBA-15, was used as a drug carrier for triamcinolone acetonide, a hydrophobic drug, with the aim of incorporating the drug formulation in a hydrophilic printable ink. The adsorption of the drug in the SBA-15 pores was confirmed by the decrease in its surface area and pore volume, along with an increase in the apparent aqueous solubility of triamcinolone acetonide, as shown by in vitro release studies. Thereafter, a hydrophilic ink composed of carboxymethyl cellulose containing drug-loaded SBA-15 was formulated and 3D printed as hydrophilic polymeric film using the semisolid extrusion technique (SSE). The 3D printed films showed complete drug release after 12 h, and the presence of the triamcinolone acetonide-loaded SBA-15 improved their in vitro mucoadhesion, suggesting their promising application in oral mucosa treatments. Besides representing an innovative platform to develop water-based mucoadhesive formulations containing a hydrophobic drug, this is the first report proposing the development of SSE 3D printed nanomedicines containing drug-loaded mesoporous silica.

Application of cellulosic materials as supports for single-step purification and immobilization of a recombinant ß-galactosidase via cellulose-binding domain.

This study aimed to develop single-step purification and immobilization processes on cellulosic supports of ß-galactosidase from Kluyveromyces sp. combined with the Cellulose-Binding Domain (CBD) tag. After 15 min of immobilization, with an enzymatic load of 150 U/gsupport, expressed activity values reached 106.88 (microcrystalline cellulose), 115.03 (alkaline nanocellulose), and 108.47 IU/g (acid nanocellulose). The derivatives produced were less sensitive to the presence of galactose in comparison with the soluble purified enzyme. Among the cations assessed (Na+, K+, Mg2+, and Ca2+), magnesium provided the highest increase in the enzymatic activity of ß-galactosidases immobilized on cellulosic supports. Supports and derivatives showed no cytotoxic effect on the investigated cell cultures (HepG2 and Vero). Derivatives showed high operational stability in the hydrolysis of milk lactose and retained from 53 to 64% of their hydrolysis capacity after 40 reuse cycles. This study obtained biocatalyzers with promising characteristics for application in the food industry. Biocatalyzers were obtained through a low-cost one-step sustainable bioprocess of purification and immobilization of a ß-galactosidase on cellulose via CBD.

Bioadhesive 3D-Printed Skin Drug Delivery Polymeric Films: From the Drug Loading in Mesoporous Silica to the Manufacturing Process.

The alliance between 3D printing and nanomaterials brings versatile properties to pharmaceuticals, but few studies have explored this approach in the development of skin delivery formulations. In this study, clobetasol propionate (CP) was loaded (about 25% w/w) in mesoporous silica nanomaterial (MSN) to formulate novel bioadhesive and hydrophilic skin delivery films composed of pectin (5% w/v) and carboxymethylcellulose (5% w/v) by 3D printing. As a hydrophobic model drug, CP was encapsulated in MSN at a 3:1 (w/w) ratio, resulting in a decrease of CP crystallinity and an increase of its dissolution efficiency after 72 h (65.70 ± 6.52%) as compared to CP dispersion (40.79 ± 4.75%), explained by its partial change to an amorphous form. The CP-loaded MSN was incorporated in an innovative hydrophilic 3D-printable ink composed of carboxymethylcellulose and pectin (1:1, w/w), which showed high tensile strength (3.613 ± 0.38 N, a homogenous drug dose (0.48 ± 0.032 mg/g per film) and complete CP release after 10 h. Moreover, the presence of pectin in the ink increased the skin adhesion of the films (work of adhesion of 782 ± 105 mN·mm). Therefore, the alliance between MSN and the novel printable ink composed of carboxymethylcellulose and pectin represents a new platform for the production of 3D-printed bioadhesive films, opening a new era in the development of skin delivery systems.

One-step purification of a recombinant beta-galactosidase using magnetic cellulose as a support: Rapid immobilization and high thermal stability.

For the first time, this work reported the one-step purification and targeted immobilization process of a ß-galactosidase (Gal) with the Cellulose Binding Domain (CBD) tag, by binding it to different magnetic cellulose supports. The process efficiency after ß-galactosidase-CBD immobilization on magnetic cellulose-based supports showed values of approximately 90% for all evaluated enzymatic loads. Compared with free Gal, derivatives showed affinity values between ß-galactosidase and the substrate 1.2 × higher in the lactose hydrolysis of milk. ß-Galactosidase-CBD's oriented immobilization process on supports increased the thermal stability of the immobilized enzyme by up to 7 × . After 15 cycles of reuse, both enzyme preparations showed a relative hydrolysis percentage of 50% of lactose in milk. The oriented immobilization process developed for purifying recombinant proteins containing the CBD tag enabled the execution of both steps simultaneously and quickly and the obtention of ß-galactosidases with promising catalytic characteristics for application in the food and pharmaceutical industries.

Synthesis of magnetic nanoparticles functionalized with histidine and nickel to immobilize His-tagged enzymes using ß-galactosidase as a model.

The aim of this study was to synthesize iron magnetic nanoparticles functionalized with histidine and nickel (Fe3O4-His-Ni) to be used as support materials for oriented immobilization of His-tagged recombinant enzymes of high molecular weight, using ß-galactosidase as a model. The texture, morphology, magnetism, thermal stability, pH and temperature reaction conditions, and the kinetic parameters of the biocatalyst obtained were assessed. In addition, the operational stability of the biocatalyst in the lactose hydrolysis of cheese whey and skim milk by batch processes was also assessed. The load of 600 Uenzyme/gsupport showed the highest recovered activity value (~50%). After the immobilization process, the recombinant ß-galactosidase (HisGal) showed increased substrate affinity and greater thermal stability (~50×) compared to the free enzyme. The immobilized ß-galactosidase was employed in batch processes for lactose hydrolysis of skim milk and cheese whey, resulting in hydrolysis rates higher than 50% after 15 cycles of reuse. The support used was obtained in the present study without modifying chemical agents. The support easily recovered from the reaction medium due to its magnetic characteristics. The iron nanoparticles functionalized with histidine and nickel were efficient in the oriented immobilization of the recombinant ß-galactosidase, showing its potential application in other high-molecular-weight enzymes.

High performance biocatalyst based on ß-d-galactosidase immobilized on mesoporous silica/titania/chitosan material.

A new support for the immobilization of ß-d-galactosidase from Kluyveromyces lactis was developed, consisting of mesoporous silica/titania with a chitosan coating. This support presents a high available surface area and adequate pore size for optimizing the immobilization efficiency of the enzyme and, furthermore, maintaining its activity. The obtained supported biocatalyst was applied in enzyme hydrolytic activity tests with o-NPG, showing high activity 1223 Ug-1, excellent efficiency (74%), and activity recovery (54%). Tests of lactose hydrolysis in a continuous flow reactor showed that during 14 days operation, the biocatalyst maintained full enzymatic activity. In a batch system, after 15 cycles, it retained approximately 90% of its initial catalytic activity and attained full conversion of the lactose 100% (±12%). Additionally, with the use of the mesoporous silica/titania support, the biocatalyst presented no deformation and fragmentation, in both systems, demonstrating high operational stability and appropriate properties for applications in food manufacturing.

A novel electrochemical platform based on mesoporous silica/titania and gold nanoparticles for simultaneous determination of norepinephrine and dopamine.

An amorphous and mesoporous silica/titania (SiTi) material was synthesized by sol-gel method and its surface was modified with gold nanoparticles (AuNP) previously stabilized in a chitosan solution. The presence of small AuNP, with diameter lower than 10 nm was confirmed by transmission electron microscopy (TEM) and UV-Vis spectroscopy. Carbon paste electrodes were prepared to test the electrochemical properties by using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) in [Fe(CN)6]3-/4- solution probe whereby the material silica-titania/gold nanoparticles (SiTi/AuNP) showed a huge improvement in the redox peak current and low charge transfer resistance. This electrode presented a good response for both norepinephrine and dopamine by means of square wave voltammetry (SWV) measurements; great sensitivity for both analytes, in an extensive linear range, was obtained. The limits of detection were 0.35 µmol L-1 and 0.57 µmol L-1 for norepinephrine and dopamine, respectively. Additionally, this electrode showed high selectivity for both analytes and it was applied in the simultaneous determination of norepinephrine and dopamine. The sensor was also tested in simulated biological fluids presenting a good recovery. The SWV electrochemical response of norepinephrine was also investigated in the presence of possible interferers such as uric acid, ascorbic acid and glucose and there was no significant interference. The prepared electrode also exhibits good reproducibility for norepinephrine detection, with relative standard deviation of 5.19%.

Designing a Support for Lipase Immobilization Based On Magnetic, Hydrophobic, and Mesoporous Silica.

A mesoporous, magnetic, and hydrophobic material was designed step by step to act as a support for lipase immobilization. Its pore size (8.0 nm) is compatible with the size of lipase from Thermomyces lanuginosus (TLL), and its hydrophobic surface (contact angle of a water drop = 125°) was planned to interact with lipase on its interfacially activated form (open conformation). The presence of magnetite particles provides magnetic retrieval of the material and enables recyclability of the biocatalysts. Regarding immobilization parameters, the hydrophobic support was tested in comparison to the unmodified hydrophilic support in phosphate buffer solution (50 mmol L-1, pH 7.5) at 25 °C. Hydrophobicity was found to be critical for the amount of immobilized TLL (immobilization yield of 97% versus 36% for the hydrophilic support), whereas the hydrophilic support favors the native conformational state and substrate access to the enzyme's catalytic site (specific activity of 5.7 versus 4.7 U g-1 for the hydrophobic support, even when it has higher TLL content). Therefore, the hydrophobic support immobilizes higher amounts of TLL and the hydrophilic support keeps the enzyme hyperactivated. Last, due to the stronger interactions of TLL with hydrophobic surfaces, the hydrophobic support offers better preservation of enzyme activity in repeated cycles (76% of activity retained after three cycles versus 50% for the hydrophilic support).

Immobilization of pectinase on chitosan-magnetic particles: Influence of particle preparation protocol on enzyme properties for fruit juice clarification.

Magnetic-chitosan particles were prepared following three different protocols enabling the preparation of particles with different sizes - nano (Nano-CMag, Micro (Micro-CMag) and Macro (Macro-CMag) - and used for pectinase immobilization and clarification of grape, apple and orange juices. The particle size had a great effect in the kinetic parameters, Nano-CMag biocatalyst presented the highest Vmax value (78.95 mg. min-1), followed by Micro-CMag and Macro-CMag, with Vmax of 57.20 mg.min-1 and 46.03 mg.min-1, respectively. However, the highest thermal stability was achieved using Macro-CMag, that was 8 and 3-times more stable than Nano-CMag and Micro-CMag biocatalysts, respectively. Pectinase immobilized on Macro-CMag kept 85% of its initial activity after 25 batch cycles in orange juice clarification. These results suggested that the chitosan magnetic biocatalysts presented great potential application as clarifying catalysts for the fruit juice industry and the great importance of the chitosan particles preparation on the final biocatalyst properties.

Magnetic biocatalysts of pectinase and cellulase: Synthesis and characterization of two preparations for application in grape juice clarification.

In the present study, we prepared two different magnetic biocatalysts of pectinase and cellulase: carrier-free magnetic CLEAs (CLEA-MP*) and immobilization on glutaraldehyde-activated magnetite (Enz-Glu-MP*). The biocatalysts were compared to their magnetic properties, immobilization parameters, stability and grape juice clarification. Enz-Glu-MP* presented higher magnetic properties than CLEA-MP*, whereas this presented higher surface area and pore volume. The KM of the enzyme immobilized on Enz-Glu-MP* was 25.65mM, lower in comparison to the CLEA-MP* (33.83mM). On the other hand, CLEA-MP* was the most active and stable biocatalyst, presenting higher recovered activity (33.4% of cellulase), higher thermal stability (2.39 stabilization factor) and improved reusability (8cycles). The integration of magnetic technology with enzymatic immobilization emerges as a possibility to increase the recover and reuse of biocatalysts for application in juice technology.

Redispersible spray-dried lipid-core nanocapsules intended for oral delivery: the influence of the particle number on redispersibility.

This study proposes a new approach to produce easily redispersible spray-dried lipid-core nanocapsules (LNC) intended for oral administration, evaluating the influence of the particle number density of the fed sample. The proposed approach to develop redispersible spray-dried LNC formulations intended for oral route is innovative, evidencing the needing of an optimization of the initial particle number density in the liquid suspension of nanocapsules. A mixture of maltodextrin and L-leucine (90:10 w/w) was used as drying adjuvant. Dynamic light scattering, turbidimetry, determination of surface area and pore size distribution, electron microscopy and confocal Raman microscopy (CRM) were used to characterize the proposed system and to better understand the differences in the redispersion behavior. An easily aqueous redispersion of the spray-dried powder composed of maltodextrin and L-leucine (90:10 w/w) was obtained, depending on the particle number density. Their surface area decreased in the presence of LNC. CRM enabled the visualization of the spatial distribution of the different compounds in the powders affording to better understand the influence of the particle number density of the fed sample on their redispersion behavior. This study shows the need for optimizing initial particle number density in the liquid formulation to develop redispersible spray-dried LNC powders.

Effects of immobilization, pH and reaction time in the modulation of α-, ß- or γ-cyclodextrins production by cyclodextrin glycosyltransferase: Batch and continuous process.

This study reports the immobilization of a ß-CGTase on glutaraldehyde pre-activated silica and its use to production of cyclodextrins in batch and continuous reactions. We were able to modulate the cyclodextrin production (α-, ß- and γ-CD) by immobilization and changing the reaction conditions. In batch reactions, the immobilized enzyme reached to maximum productions of 4.9mgmL-1 of α-CD, 3.6mgmL-1 of ß-CD and 3.5mgmL-1 of γ-CD at different conditions of temperature, pH and reaction time. In continuous reactor, varying the residence time and pH it was possible to produce at pH 4.0 and 141min of residence time preferentially γ-CD (0.75 and 3.36mgmL-1 of α- and γ-CD, respectively), or at pH 8.0 and 4.81min α- and ß-CDs (3.44 and 3.51mgmL-1).

Palladium(II) chemically bonded to silica surface applied to the separation and identification of polycyclic aromatic sulfur heterocycles in heavy oil.

Separation of polycyclic aromatic sulfur heterocycles among themselves and also from interferents in petrochemical matrices is a challenging task because of their low concentration, matrix complexity, and also due to the presence of polyaromatic hydrocarbons, as they present similar physico-chemical properties. Therefore, the objective of this work was preparation, characterization, and application of a stationary phase for separation of these compounds in a heavy gas oil sample and their identification by comprehensive two-dimensional gas chromatography. The stationary phase was prepared by grafting mercaptopropyltrimethoxisilane onto a silica surface, followed by palladium(II) chloride immobilization. Elemental analysis, thermogravimetry, nitrogen adsorption-desorption isotherms, infrared analysis, and scanning electron microscopy were performed to characterize this solid phase. Sulfur compounds were separated in an open column packed with the stationary phase and analyzed by comprehensive two-dimensional gas chromatography coupled to time-of-flight mass spectrometric detection. The number of compounds tentatively identified was 314 and their classes were thiophenes, benzotiophenes, dibenzothiophenes, naphthothiophenes, benzonaphthothiophenes, and dinaphthothiophenes. Separation among sulfur compounds and polyaromatic hydrocarbons was successful, which is a difficult goal to achieve with the traditionally employed solid phases. Some recalcitrant compounds (dibenzothiophenes with substituents of two and four carbons) were fully separated and tentatively identified.

Comparison between pre-fractionation and fractionation process of heavy gas oil for determination of sulfur compounds using comprehensive two-dimensional gas chromatography.

The separation of the organic sulfur compounds (OSC) of petroleum or its heavy fractions is a critical step and is essential for the correct characterization of these compounds, especially due to similar physical and chemical properties of polycyclic aromatic sulfur heterocycles (PASH) and polycyclic aromatic hydrocarbons (PAH). This similarity results in coelutions among PAH and PASH and for this reason former steps of fractionation are required before gas chromatographic analysis. The objective of this study was to evaluate the potential of GC×GC for the separation and identification of OSC in a heavy gas oil sample without fractionation, after pre-fractionation in an alumina column and also after fractionation process. This last one was performed with a modified stationary phase manufactured and characterized in the laboratory, called Pd(II)-MPSG, where palladium is chemically linked to silica through mercaptopropyl groups. The fractions obtained from both procedures were analyzed by GC×GC/TOFMS, which was effective to separate and identify various classes of OSC. A hundred and thirty-five compounds were tentatively identified in the sample that was only pre-fractionated. However, when the fractionation was also performed with the Pd(II)-MPSG phase, a larger number of sulfur compounds were found (317). Results have shown that the analysis of a pre-fractionated sample by GC×GC/TOFMS is suitable when the goal is a general characterization of classes of compounds in the sample, while a more detailed analysis of PASH can be performed, using also the fractionation Pd(II)-MPSG phase. GC×GC/TOFMS played a major role in the comparison of samples obtained from pre-fractionation and fractionation steps due to its high peak capacity, selectivity, organized distribution of chromatographic peaks and resolution.

Evidence for excited state intramolecular charge transfer in benzazole-based pseudo-stilbenes.

Two azo compounds were obtained through the diazotization reaction of aminobenzazole derivatives and N,N-dimethylaniline using clay montmorillonite KSF as catalyst. The synthesized dyes were characterized using elemental analysis, Fourier transform infrared spectroscopy, and (13)C and (1)H NMR spectroscopy in solution. Their photophysical behavior was studied using UV-vis and steady-state fluorescence in solution. These dyes present intense absorption in the blue region. The spectral features of the azo compounds can be related to the pseudo-stilbene type as well as the E isomer of the dyes. Excitation at the absorption maxima does not produce emissive species in the excited state. However, excitation around 350 nm allowed dual emission of fluorescence, from both a locally excited (LE, short wavelength) and an intramolecular charge transfer (ICT, long wavelength) state, which was corroborated by a linear relation of the fluorescence maximum (ν(max)) versus the solvent polarity function (Δf) from the Lippert-Mataga correlation. Evidence of TICT in these dyes was discussed from the viscosity dependence of the fluorescence intensity in the ICT emission band. Theoretical calculations were also performed in order to study the geometry and charge distribution of the dyes in their ground and excited electronic states. Using DFT methods at the theoretical levels BLYP/Aug-cc-pVDZ, for geometry optimizations and frequency calculations, and B3LYP/6-311+G(2d), for single-point energy evaluations, the calculations revealed that the least energetic and most intense photon absorption leads to a very polar excited state that relaxes non-radioactively, which can be associated with photochemical isomerization.

Solid phase extraction of petroleum carboxylic acids using a functionalized alumina as stationary phase.

Petroleum essentially consists of a mixture of organic compounds, mainly containing carbon and hydrogen, and, in minor quantities, compounds with nitrogen, sulphur, and oxygen. Some of these compounds, such as naphthenic acids, can cause corrosion in pipes and equipment used in processing plants. Considering that the methods of separation or clean up the target compounds in low concentrations and in complex matrix use large amounts of solvents or stationary phases, is necessary to study new methodologies that consume smaller amounts of solvent and stationary phases to identify the acid components present in complex matrix, such as crude oil samples. The proposed study aimed to recover acid compounds using the solid phase extraction method, employing different types of commercial stationary ion exchange phases (SAX and NH(2)) and new phase alumina functionalized with 1,4-bis(n-propyl)diazoniabicyclo[2.2.2]octane chloride silsesquioxane (Dab-Al(2)O(3)), synthesized in this work. Carboxylic acids were used as standard mixture in the solid phase extraction for further calculation of recovery yield. Then, the real sample (petroleum) was fractionated into saturates, aromatics, resins, and asphaltenes, and the resin fraction of petroleum (B1) was eluted through stationary ion exchange phases. The stationary phase synthesized in this work showed an efficiency of ion exchange comparable to that of the commercial stationary phases.

Nanocapsule@xerogel microparticles containing sodium diclofenac: a new strategy to control the release of drugs.

The aim of this work was to evaluate the potentiality to control the drug release of a new architecture of microparticles organized at the nanoscopic scale by assembling polymeric nanocapsules at the surface of drug-loaded xerogels. Xerogel was prepared by sol-gel method using sodium diclofenac, as hydrophilic drug model, and coated by spray-drying. After coating, the surface areas decreased from 82 to 28 m(2)/g, the encapsulation efficiency was 71% and SEM analysis showed irregular microparticles coated by the nanocapsules. Formulation showed satisfactory gastro-resistance presenting drug release lower than 3% (60 min) in acid medium. In water, the pure drug dissolved 92% after 5 min, uncoated drug-loaded xerogel released 60% and nanocapsule coated drug-loaded xerogel 36%. After 60 min, uncoated drug-loaded xerogel released 82% and nanocapsule coated drug-loaded xerogel 62%. In conclusion, the new system was able to control the release of the hydrophilic drug model.